Amplificator Bose PowerShare PS602 adaptable power amplifier

The PS602 is a 2-channel installed amplifier that allows its total 600 watts to be shared across both outputs. Independently control the output level, EQ, and low-impedance/high-impedance (Low-Z/Hi-Z) settings for each output. Onboard configurable loudspeaker processing and direct access to zone controllers eliminate the need for an additional signal processor in many installations.

Mai multe detalii

Bose PowerShare PS602
Produs nou

6 825,00 lei

- +

Alerteaza-ma cand scade pretul

 
Mai multe detalii
  • Amplifier Power 2 x 300 W (THD+N < 0.04%, 1 kHz, 4-8 Ω, 70/100V)
  • Maximum Power per Channel 600 W @ 4-8 Ω, 70/100V
  • Gain (Low-Z mode) 44 dB, RCA (unbalanced) inputs; 32 dB, Euroblock (balanced) inputs
  • Gain (70V mode) 47 dB, RCA (unbalanced) inputs; 35 dB, Euroblock (balanced) inputs
  • Gain (100V mode) 50 dB, RCA (unbalanced) inputs; 38 dB, Euroblock (balanced) inputs
  • AUDIO PERFORMANCE
  • Frequency Response 4-8 Ω: 20 Hz – 20 kHz (+/- 0.5 dB @ 1 W); 70/100V: Same as 4-8 Ω with 50 Hz high-pass filter
  • Channel Separation (Crosstalk) > 85 dB @ 1 kHz, > 65 dB @ 20 kHz
  • Signal to Noise Ratio 100 dB (at rated power, A-weighted)
  • AUDIO INPUTS
  • Input Channels 2 unbalanced, 2 balanced
  • Connectors Stereo RCA, 3-pin Euroblock
  • Input Impedance 10 kΩ (RCA), 20 kΩ (Euroblock)
  • Maximum Input Level 20 dBu (at 12 dBu sensitivity setting)
  • Sensitivity -10 / -2 dBV, RCA inputs; 4 / 12 dBu, Euroblock inputs (low / high sensitivity)
  • AUDIO OUTPUTS
  • Outputs 2
  • Connectors 2-pin inverted Euroblock
  • INTEGRATED DSP
  • A/D and D/A Converters 24-bit / 48 kHz
  • Processing Functions Matrix mixer, loudspeaker EQ, real-time 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity
  • inversion
  • Loudspeaker Presets Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105 and RMU108
  • Audio Latency < 1 ms (any input to speaker output)
  • INDICATORS AND CONTROLS
  • Power LED Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault. Solid red: Supply fault.
  • Input Signal LED Green: Signal present. Amber: Input is near clipping. Red: Input is clipping. Solid red: Indicates a fault.
  • Output Limit LED Amber: Amplifier limiting an output. Blinking red: Amplifier muted. Solid red: Indicates a fault.
  • Controls, Front Panel Power On/Off
  • Controls, Rear Panel Amplifier mode DIP switches, loudspeaker EQ dials, output attenuators
  • ELECTRICAL
  • Mains Voltage 100 VAC – 240 VAC (±10%, 50/60 Hz)
  • AC Power Consumption 120 VAC: 14 W (Standby), 700 W (Max) 230 VAC: 14 W (Standby), 700 W (Max)
  • Mains Connector Standard IEC (C14)
  • Maximum Inrush Current 14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)
  • Protections High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage
  • PHYSICAL
  • Dimensions (H x W x D) 44 mm x 483 mm x 414 mm (1.7” x 19.0” x 16.3”)
  • Shipping Weight 6.9 kg (15.3 lb)
  • Net Weight 5.5 kg (12.2 lb)
  • Cooling System Microprocessor controlled, variable speed fans, left to right air flow
  • GENERAL
  • Inputs (Control) RJ-45 remote input for volume control using the CC-1 ControlCenter zone controllers, or for connection to the CV41.
  • USB input for configuring the amplifier with PowerShare Editor software. Mute input control.

Scrieţi o recenzie

Amplificator Bose PowerShare PS602 adaptable power amplifier

The PS602 is a 2-channel installed amplifier that allows its total 600 watts to be shared across both outputs. Independently control the output level, EQ, and low-impedance/high-impedance (Low-Z/Hi-Z) settings for each output. Onboard configurable loudspeaker processing and direct access to zone controllers eliminate the need for an additional signal processor in many installations.

Scrieţi o recenzie

 
Comments(0)

Nu sunt opinii ale clienților în acest moment.

Încă 30 produse în aceeași categorie:

Nu sunt produse

Se va calcula Livrare
0,00 lei Total

Finalizare